Palazzo Capri Smooth 2-Panel Square Solid Core Primed Composite Interior Door Slab Clear All Go to All Filters Clear All Go to All FiltersKrosswood Rustic Knotty Alder 2-Panel Square Top Solid Core Prehung Interior Door 24 in. x 80 in. French Knotty Alder 10-Lite Tempered Glass Solid Wood Right-Hand Single Prehung Interior Door 37.5 in. x 81.75 in. Unfinished Pine Half Louver 1-Panel Single Interior Door 30 in. x 96 in. Krosswood French Knotty Alder 12-Lite Tempered Glass Solid Wood Left-Hand Single Prehung Interior DoorKnotty Alder 2 Panel Square Top V-Groove Solid Wood Right-Hand Single Prehung Interior Door Rustic Knotty Alder 2-Panel Top Rail Arch Solid Wood Core Single Prehung Interior Door Krosswood Craftsman Rustic Knotty Alder 3-Panel Shaker Solid Core Prehung Interior DoorPrimed 2-Panel Flat Single Interior Door 30 in. x 80 in. Rustic Prefinished 2-Panel V-Groove Solid Core Knotty Alder Wood Reversible Single Prehung Interior Door 33.5 in. x 81.75 in.

Knotty Alder 2 Panel Top Rail Arch V-Groove Solid Wood Left-Hand Single Prehung Interior DoorRustic Knotty Alder 1-Lite with Solid Wood Core Left-Hand Single Prehung Interior Door 31.5 in. x 81.75 in. 35.5 in. x 81.75 in. Unfinished Red Oak 6-Panel Red Single Interior Door32 in. x 96 in. MODA Primed White 5-Panel Solid Core Wood Interior Door SlabAn interior door upgrade can rejuvenate any space, especially when it brings in natural light, as does this Masonite Door with Privacy Glass. It’s not hard to install an interior slab door (as opposed to a pre-hung door). Follow our step-by-step tutorial and learn how to give any room a whole new look. Here is a before and after shot of the room where we’re adding the new door. As you can see, this one simple DIY can make a huge difference. Measure for the new door slab by checking the old door’s width in three places — across the top, middle and bottom of the door. Jot down the widest dimension. Next, measure the door’s  height and thickness.

Before removing the old door, remove the knob and any hardware off the old door frame using the appropriate screwdriver or drill and drill bit. To remove the old door, start by backing the screws out of each hinge on the door slab with a screwdriver or drilling and pulling it away from the door frame. Next, dry fit the new interior slab door in the opening, using shims to hold it in place if needed. If the new door doesn’t fit, the old door can be used as a template to indicate where the new door slab should be trimmed. Simply place the new door on a flat work surface, then place the old door on top of it, making sure to align both doors in the same direction (right side up, opening to same direction, etc.). Mark the bottom of the old door on the new door with a pencil. Next, with a utility knife, score along that line, then using a circular saw, trim the new door slab to size. Sand any rough edges as needed with an orbital sander. Note: Be sure to wear appropriate safety glasses and protective work gloves when using power tools.

Again, using the old door as a template, with a pencil, mark on the new door where the hinges and door knob will be located.garage door springs raleigh nc Score the line around the hinges with a utility knife, then notch the perimeter and interior of hinge area with a hammer and chisel.how much do larson storm doors cost Next using the chisel, gradually skim off the notches.mini 5 door hatch insurance group Once notching is complete, attach the new hinges to the new door.motorized garage door screen pricing Secure the door lockset kit onto the door using the provided screws, then using the hole saw bit, drill into one side, then the other.new front door chichester

Next, drill into the side edge of the door to create a hole for the latch.interior glass doors liverpool While the door is lying flat, install the latch portion of the new knob by tracing around it, then scoring with a utility knife and chiseling it out using the same method from Step 7, so that the latch lays flush against the door edge. Once the latch is in place, move the new door to its location, add shims to adjust the door’s height and attach the other side of all hinges to the door frame. Hang the door and check the fit. If adjustments are needed, remove the door and sand or trim the door with a planer, as needed, then reinstall the door. If the fit is good, leave the door in place, and move on to finishing the lockset installation. Install the lockset using a Philips screwdriver. Follow the instructions that came with your particular lockset. Install the latch plate into the door frame by lining it up with the latch from the door knob, then scoring/chiseling as we did in Step 10 with the hinges.

If your door features glass, be sure to leave the protective plastic on until you’ve finished painting your door. Allow the paint to dry completely, and you’re done! Browse our selection of Masonite Doors at The Home Depot. Take a look at more DIY projects here on The Home Depot blog, and follow our Easy DIY Projects board on Pinterest. Is your idea of DIY is hiring a professional? Let us do it for you. Contact The Home Depot Home Services. Sort by: Top Sellers Sort by: Most Popular Sort by: Price Low to High Sort by: Price High to Low Sort by: Top Rated Products 6-Panel Unfinished Red Oak Interior Door Slab 2-Panel Arch Solid Core Oak Interior Door Slab 32 in. x 80 in. 6-Panel Unfinished Red Oak Interior Door Slab with Bore Modern Full Lite Solid Core Pine Reed Glass Interior Door Slab Krosswood Craftsman Rustic Knotty Alder 3-Panel Shaker Solid Core Interior Door Slab Select 2 to 4 Items to CompareCraftsman Style TrimCraftsman Style Interior DoorsWhite CraftsmanCraftsman InteriorsFront CraftsmanPainted CraftsmanInteriors InteriorCraftsman KitchenNew Interior DoorsForwardinterior doors in white craftsman style, I want these doors.