concrete screws with Phillips-heads When it comes to fighting a hurricane or violent wind storm your best bet is to be prepared. The amount of material you'll need to build and install each plywood hurricane shutter will vary according to the size of the window you want to protect. The instructions and materials listed are based on construction of a hurricane shutter to cover a typical residential window. After measuring your window, cut the sheet of 5/8" CDX grade exterior plywood 7" wider and 7" taller than the window you want to cover, thus providing 3" or 4" of protective overhang on all sides of your window. Some home centers will cut to your size specifications for free or for a fee. To install your plywood hurricane shutter on a home built with "frame" construction, measure and locate the framing studs. After locating the framing studs and measuring carefully, drive the #8 or #10 Phillips-head wood screws (2" to 2-1/2" long) through the plywood and into the center of the studs above, below and at the sides of each window (approximately 7/8" outside the window frame).

The screws must hit the studs solidly to provide an adequate anchor for your plywood shutter. For an alternate method, after locating the framing studs and making careful measurements, nail the plywood hurricane shutter over the window you wish to protect. Once more, make sure to drive each nail into the center of the studs above, below and to the sides of the window (approximately 7/8" outside the window frame). Nails are not as secure as screws and might be harder to remove without damaging your plywood, but if you do not own an electric screwdriver, this option might be easier. To install a hurricane shutter on a home built with concrete blocks -- or stucco over concrete blocks -- you once more begin with the same 5/8" CDX plywood shutter cut 7" wider and 7" longer than the window you want to cover. Concrete block construction, however, requires different fastening hardware and a different technique than does a frame home. With the concrete bit, drill 10 holes into the concrete wall all around your window.

Each hole should be 2" to 3" from the edge of the window to keep the concrete from chipping or breaking. Insert the 5/16" x 3" hanger bolts in these 10 holes. After careful measurement, drill ten 5/16"-diameter holes into the plywood shutter to correspond precisely to each of the 10 hanger bolts you just installed. garage roller door melbourneSlide the plywood over the protruding ends of the hanger bolts, place a washer on each bolt and then fasten tightly with the ten 5/16" wing nuts.upvc door hinge bolts For an alternate method of fastening a plywood shutter to a concrete structure, drive the 1/4" concrete screws through the plywood shutter and into the concrete block wall of the house, again making sure the screws are 2" to 3" from the edge of the window to prevent the concrete from chipping.sliding patio door weatherstripping

Note: A handy kit (KwikTap) includes everything you'll need in a single box -- a concrete bit, concrete screws and Phillips-head driver bit. Sign up for weekly project ideas and advice from experts Privacy Policylarson storm door directions Sign Up for Morecheapest belt drive garage door opener We love to DIY. concealed door closer price listYou love to DIY. See the latest DIY projects, catch up on trends and meet more cool people who love to create. Make It. Fix It. Learn It. Find It. Get quick inspiration from Made + Remade each week. The Essential Steps to Landscape DesignTry These Plants and Groundcovers 10 Things You Must Know About Landscaping

Reducing the Size of a Lawn Lush Landscaping Creates Major Curb Appeal How to Design a Great Yard with Landscape Plants How to Landscape a Shady Yard Popular Landscaping Groundcovers and Shrubs How to Landscape a Sloping Backyard Some of the Most Desperate LandscapesPGT® is the authority on impact-resistant windows and doors. After Hurricane Andrew devastated South Florida and caused billions of dollars in damage, PGT worked with Miami-Dade County to establish new codes and testing protocols to give greater protection to people and property when the next storm hit. And so WinGuard® was born – the first full suite of impact-resistant windows and doors. Since then, WinGuard has been among the strongest, safest and most-reliable products in the industry, and now we’ve made it even better.Our new PGT WinGuard Vinyl products feature their most-attractive profile ever, with larger sizes capable of handling the highest design pressures. The new and improved WinGuard Vinyl still meets the toughest hurricane codes in the country.

It still protects against flying debris, intruders, outside noise and UV rays. It’s still everything you love about the nation’s #1 brand of impact-resistant windows and doors—plus a whole lot more.This is one product line that fits every need, so there’s no reason to compromise. You can have the same great look and same robust construction throughout your home, in every frame small to large. PGT WinGuard Vinyl windows and doors provide continuous, effortless hurricane protection – as well as protection from intruders, UV rays, and outside noise. No more wrestling with ugly, metal shutters. No more hanging even uglier plywood. Which means there’s one more thing WinGuard protects: the beauty of your home.WinGuard Vinyl windows and doors:• Feature laminated insulating glass to provide an all-in-one solution for continuous, effortless hurricane protection• Help deter intruders and are backed by one of the industry’s best warranties• Significantly reduce outdoor noise and filter out 99% of damaging UV rays• Offer ENERGY STAR® qualified configurations• Are customizable with frame colors, hardware finishes, glass tints, grid styles and patternsWith all these benefits

, it’s easy to see why PGT WinGuard is the best-selling brand of impact-resistant windows and doors. All PGT Residential Products Warranty Optional Accidental Glass Breakage Warranty You can be confident in our engineering. PGT® windows and doors are continuously tested and validated by the industry's most-respected accredited organizations. The certifications we earn are your assurance that our products will perform as expected.PGT WinGuard® Vinyl product certifications, ratings, and testing include:• Miami-Dade Notice of Acceptance• AAMA Tested/Keystone Certified• Florida Product Approval• International Building Code• ENERGY STAR®• National Fenestration Rating Council® (NFRC)• Texas Department of Insurance• STC (Sound Transmission Class)• OITC (Outdoor-Indoor Transmission Class)• Manufactured Housing (AAMA 1701) PGT has its own state-of-the-art testing lab, where we spend hundreds of hours analyzing and evaluating our products. Consider it extra assurance that the windows and doors you buy will deliver optimum performance for years to come.

PGT WinGuard Vinyl windows and doors are designed to meet or exceed the International Building Code for:• Air infiltration• Water resistance• Deglazing• Forced-entry resistance• Structural integrity• Small and large missile impact protection• Residential intruder protection New WinGuard Vinyl means to youHurricane ProtectionDuring a hurricane, flying debris can break the glass in regular windows and doors, resulting in wind and water damage inside your home. WinGuard Vinyl products can withstand repeated impact from a nine pound 2' x 4' beam traveling at 34 miles per hour, followed by hurricane-force winds. Even if the glass is damaged, it will remain secure in its frame and continue to keep the elements outside.Breaking a window is the most common means of entry for an intruder. While non-impact resistant glass shatters easily upon contact and offers little resistance, the durable interlayer used in WinGuard Vinyl products will keep the glass in place and provide an additional barrier that deters intruders.