Have your home make a statement with an entrance from Doors-N-More. Your door is more than an entrance, it’s a first impression. The possibilities are endless for your perfect door. Custom finishing is available. See more doors and options at: Masonite Need to close that new door? Doors-N-More carries a wide array of door knobs, levers, and handle sets. All are offered in today’s hot finishes as well as the classics. Visit the showroom for a sampling. To see all the options, visit: ]” /” target=”dnmwindow”>Larson Storm DoorsVinyl cloth or fiberglass are the most durable types of screen mesh and come in a variety of colors and shades. Aluminum screens provide excellent visibility, but are subject to damage. Solar fiberglass screens cut down on the amount of UV rays and sunlight and are great for protecting furniture or wall-to-wall carpet. This type of screen is more expensive than others. In this demonstration, we used fiberglass mesh.

Once you've removed the screen frame from the window, lay the frame on a flat surface and roll out enough replacement screen that it covers the entire frame. Make a cut across the roll with sufficient excess to clamp around the edges of the frame while you work. The screen is held in the frame by a plastic spline that runs along a channel around the perimeter of the frame. Use a nail-punch or other sharp object to loosen the end of the spline and pull it up from the channel and out of the frame. The screen should come out easily once you've removed the spline. It may be helpful to wash the screen frame before continuing, or you can use compressed air to blast out any dirt. When laying the new screen over the frame, lay it out with the curved or concave side down. This will make it easier to install the screen and ensure that the new piece lies flat in the frame. You can then use clamps to hold the screen taut onto the frame while you work. It's advisable in most cases to replace the spline along with the screen material.

Spline is inexpensive and can be purchased at most home stores (Image 1). Once you've creased the screen all the way around the frame, begin placing the spline in the channel. Start on one side and use your fingers to push the spline into the channel from one side of the screen to the other (Image 2). Try to install the material so that it is neat and flat, but don't worry about getting the screen overly tight. Unspool a length of spline and install it by pressing it into the frame's groove using a rolling spline-tool (Image 1). Gently pull the spline tight with one hand as you carefully press it into the groove with the roller (Image 2). As the spline goes into the groove, it helps pull the screen taut. When you reach the corners of the frame where the roller won't reach, use a flat-head screwdriver to press the spline into the corner. Always work in the same direction with the roller -- don't back the wheel up. Be careful not to allow the roller to slip out of the groove as it could damage the screen mesh.

When you have installed spline all the way around the frame and come back to the starting point, trim the spline to length using a utility knife. sliding door for arched doorwayAlso use the utility knife to trim off the excess screen mesh from the outside of the frame. garage door remote circuit diagramAllow the blade to ride along the outside of the frame's groove to ensure a straight, clean cut.wooden screen doors lancaster paHaving indoor or outdoor wooden doors are beautiful additions to any home. sliding glass door adapter portable air conditioner

Like most things, wooden doors can start to develop problems. garage door repair sugar land texasCracks, an improper seal or excessive heat and moisture can cause your wooden door to warp. windows and doors maidstoneA warped door allows air to escape or enter your home, as well as bugs and rodents! Fortunately, knowing how to fix a warped wooden door can save you time, money and the hassle of installing a new door. With a little bit of elbow grease and some patience, your beautiful wooden door can be fixed in no time. What You Need to Fix a Warped Wooden Door: Heavy towels or a large blanket 50-lb sandbag or something of equal weight Fixing a Warped Wooden Door After you’ve gathered the supplies you need, fixing a warped wooden door is simple! Before you remove your wooden door from the hinges, place both of your sawhorses four to five feet apart in a covered area.

Use your screwdriver and remove the door from the hinges and lay it across both of the sawhorses. Be sure to lay the door down with the bowed side facing up. After you’ve placed your door on the sawhorses, use your sandpaper and and the top and bottom of the door. How to Repair and Flatten a Warped Door After the door has been taken off the hinges and proper sanded on the top and bottom portion, check to see how badly your wooden door is warped. Once you’ve assessed the level of damage to the door, you will know what methods to use to flatten a warped door. If your door is only slightly bowed, take the sandbag or object of similar weight, and lay it across the area that is warped. Leave the sandbag on the door for 24 hours or until the warp is completely gone. If your door is badly warped, wet your heavy towels or large blankets and lay them across the warped area only. Each day, rewet the towels and add five to 10 pounds of weight onto the door until is is completely straight again.