sliding barn door directions
Sliding barn door hardware holds a large door next to a wall and includes a track that allows the door to slide laterally. A set of hardware usually includes barn door rollers, a track, stops, mounting screws, and brackets that attach to the door. Installing the hardware is easy, but requires careful work; precision is essential for the door to operate smoothly. Use a tape measure to determine the height of your door. Add 2 inches of clearance to this measurement to get the total height. Examine your barn door hardware kit, and determine where the top of the door sits relative to the track; Ask a helper to hold the track above the door, and measure from the point you identified to the floor. Adjust the track until the point sits at the total height. Sit a level on top of the track, and adjust the track until the level is perfectly horizontal. Insert a pencil into the mounting holes on the track, and make marks on the wall at the center points. Read the manufacturer's recommendations for your hardware kit.
If you plan to mount the hardware directly to the wall, insert a drill bit onto a power drill and drill a small pilot hole at each of your marks. These holes enable you to center the mounting screws. If you are using a heavy door, if the mounting holes are not located above studs, or if the wall is not strong enough to hold the full weight, install drywall spacers and shims at each of the mounting holes. This process offers extra strength and prevents the wall from crumbling under the weight of the door. Ask a friend to hold the barn door track against the wall. Center the mounting holes over the pilot holes or spacers. Use your electric drill to drive the mounting screws through the holes and into the wall. Tighten the screws until they hold the track against the wall, but avoid tightening them too far. Use your level to ensure that the track is horizontal. Push the end caps or stops into place on either end of the track. Find the brackets and barn door rollers that came with your hardware kit.
Screw the brackets into the rollers, making sure to place washers between the nuts and bolts. Place the rollers into the track, and verify that the brackets face the right direction. Roll the rollers along the track from end to end, and ensure that they move smoothly. Ask your helper to hold the door up to the brackets. Keep in mind that the installation style varies; some brackets mount to the top edge of the door, while others mount to the front or back of the door. Hold the door in place, check to verify that the door is level, and mark the location of each mounting hole. Remove the doors, and lift the brackets and rollers out of the track. Use the mounting screws or bolts to fasten the brackets to the door. Lift the door back into the track, and test the motion along the full track length. The right tools make it easier to install sliding barn door hardware safely on any wall. On eBay, you can buy all of the necessary supplies without visiting the hardware store. Simply use the eBay search bar to search for the name of a product, and refine the results with the search filters.
Top Mount Hanger Type Single Extrusion Box Rail Fascia Track Type Mill Grade Aluminum Track Finish Commercial Grade Top Hung Wall Mount Sliding Door Hardware *With Ball Bearing Hangers The 2610F is a versatile and easy to install wall mounted sliding door hardware set ideally suited for application where the installation of a Pocket Door is not structurally possible or not cost effective.
andersen french door adjustment instructionsPossible applications include closets, storage rooms or anywhere space is limited and a wall mounted sliding door will suit.
front door knob won't unlockThe 2610F is for interior use only and not suited for external applications. Wall mount sliding door hardware sets for standard door/opening installations (doors, jambs, opening trim, door locks, door pulls NOT included).
Track CAN be cut down to fit smaller door/opening widths. Minimum 24" door width required for soft-close/open operation How to order 2610F Hardware Sets: 1. Determine your door size (door width and door thickness) 2. Specify door weight (125lbs or 200lbs Max.) 3. Select a part set number that accommodates your door size and maximum door weight. 2610F Series Instalation Instructions 2610F Extened Jamb Latch Instructions 2610F Series Quick Reference Drawings 200lbs. [91kg] (W/1125 Ball Bearing Door Hanger) 1" [25mm] to 1-3/4" [44mm] Mill Grade Aluminum or Anodized Aluminum Single Packed, Reinforced Corrugated Box Oversized item must be shipped freight. Include this item, entire order ships for $125 continental nation-wide. Freight orders over $500 ship free! Questions, call our internet order department @ 1-800-837-5664Create your free profile Resume full episodes across devices Use this one profile to sign into all your A+E Networks profiles: A&E, FYI, HISTORY and Lifetime!
Please enter your first name Please enter a valid email Please enter your password Passwords do not match Please enter a valid Year of Birth You must accept the terms of use and privacy policy. Yes, sign me up to receive emails.* I agree to the terms of use and privacy policy. Already have a profile? * By creating a profile, you agree to receive emails from and A+E Networks. You can opt out at any time. You must be 13 years or older and a resident of the United States. Contact us for more details. You will soon receive an activation email. To activate your profile, simply click on the link within that email. If you do not receive this email, . To ensure delivery to your inbox, please add us to your address book. You have previously signed up but your profile was never confirmed. Please enter your email address below, and we will resend the activation email. Simply click on the link within that email to complete your registration.