Garage Opener Buying Guide imageA garage is a safe and convenient space for people who want closed storage for their vehicle and other items such as gardening tools, an additional freezer, or seasonal decorations. A garage opener is...Read More about Garage Opener Buying GuideGenie manufactures a variety of remote controls compatible with the Intellicode system that will operate your opener once you program the remote to communicate with the opener motor. Programming your Genie Intellicode model H6000A garage door remote becomes necessary when adding a second remote, replacing a lost remote, changing remotes for new tenants or after retaining ownership of the home from the previous owners. Look above your Genie garage door opener for the two screws holding the light bulb cover to the front of the motor. Remove the screws and lower the cover. Find the learn button to the left of the light bulb socket. Depress the learn button and quickly release it. The red LED beneath the learn button will blink twice each second once you release the button.

Press the button on your remote within 30 seconds of releasing the learn button. The red LED beneath the learn button will stop flashing and remain lit. Press the remote control button once again to complete the programming and extinguish the red LED. Raise the light bulb cover on the Genie opener motor. Secure the cover with the two screws you removed. Things You Will Need Stepladder Screwdriver Tip References Genie: Genie Screw Drive Garage Door Opener Series IS, ISL, IC, H Suggest a CorrectionBelow is information to help you program your Garage Door Operator remote control or outside keypad. If you need additional help, feel free to give a call for assistance or to schedule a service call to program for you. CHAMBERLAIN / LIFTMASTER / SEARS CRAFTSMAN GARAGE DOOR OPENERS Programming 971LM and 973LM, 371LM and 373LM Security Plus Transmitters LIFTMASTER AND SEARS CRAFTSMAN WIRELESS KEYPADS 976LM, 377LM Security Plus and 66LM Wireless Keyless Entry Systems The square smart button is located on the side or the back of the motor head, and is colored red, green, amber, orange, or purple.

It is directly under the #1 wire terminal screw. Programming Genie Intellicode Remote Transmitters ** To erase all Intellicode remotes and wireless keyless entry, hold down on the learn button until the indicator light stops blinking, then proceed to Step 2.double glazed door jammed These transmitters work by matching the settings on the internal code setting switches with the same set of switches in the receiver on the garage ceiling. sliding screen door jammedThe receiver is located either behind the light lens of the Genie garage door opener motor head, or inside an external small rectangular box on the ceiling, which is connected to the motor head by a set of wires. chi garage door cost

Note: the frequency of the transmitter must be the same frequency as the receiver on the ceiling for it to work. Genie has been making the 390 MHz frequency exclusively for the last 15 years. These garage door opener transmitters have 2 smaller switches to the right of the internal Code Setting Switches. sliding garage door bottom sealThe small right switch should be set according to how many Code Setting Switches in your receiver (either 9 or 12). automatic garage door conversion sydneyThe small left switch is for programming purposes. bifold door track hardwareTo program a button for one of your doors, follow the instructions below: Genie Garage Door Opener Wireless Keypad Model GPWK-12, GWK

(works with remotes having 9 or 12 internal code setting switches. Keypad is black with a slide-up cover showing the Genie logo only) This keyless garage door opener entry pad works with Genie transmitters using 390 MHz frequency. It is NOT compatible with Genie Intellicode transmitters (if your keypad has Intellicode printed on the cover, go to the next set of programming instructions below). The Door Code in the Step-By-Step Procedure at right is determined by the internal code switches inside your transmitter and the accompanying chart. Determine the settings of the first 3 switches and write down the corresponding number from the chart. Continue with the next 3 switches and its corresponding number, and so on, until the last set of 3 switches. You should have 3 or 4 Door Code numbers. Door Code in Step #4: ____ ____ ____ ____ Model 1: Intellicode Model GWKIC, ACSDG (black with slide-up cover and the word “Intellicode” printed on the cover) GWKIC, ACSDG, Two Part, Step-By-Step Programming

To Reset the Intellicode Wireless Keypad To Program the Intellicode Wireless Keypad NOTE: If red indicator light does not blink, it is not taking the programming steps. Check the 9 volt battery under the keypad numbers. To access, press inward, under the number pad lip while sliding downward to expose the battery. Press the Receiver Learn Code button on the Power Head Receiver of your Genie Garage Door Opener. This small black button is located behind the light lens at the motor head and is nearest the floppy 6 inch antenna wire that protrudes from the power head. When pressed, a radio signal indicator will start blinking red for 30 seconds. Adding More Doors to Keypad: With most Genie units, remove the light lens globe to expose the Learn Button on the motor head. The learn button is sometimes located on the back of the unit, or with Accelerator openers, it is under the light lens near the hinge of the lens globe. Always locate the floppy antenna wire first.