FB31 Automatic Flush BoltFB32 Automatic Flush Bolt, Top Bolt with Auxiliary Fire LatchFB33 Automatic Flush Bolt, Top Bolt with Auxiliary Fire Latch and Retrofit PlateFB41 Automatic Flush BoltFB42 Automatic Flush Bolt, Top Bolt with Auxiliary Fire Latch Constant Latching Flush Bolt FB51 Constant Latching Flush BoltFB52 Constant Latching Flush Bolt, Top Bolt with Auxiliary Fire LatchFB53 Constant Latching Flush Bolt, Top Bolt with Auxiliary Fire Latch and Retrofit PlateFB61 Constant Latching Flush BoltFB62 Constant Latching Flush Bolt, Top Bolt with Auxiliary Fire Latch 261 Manual Flush Bolt262 Manual Flush Bolt265 Manual Flush BoltFB358 Manual Flush BoltFB457 Manual Flush BoltFB458 Manual Flush Bolt DP1 Dust Proof StrikeDP2 Dust Proof Strike Coordinators, Filler bar, Mounting Brackets, Carry Bar COR Bar CoordinatorFL Filler BarMB1 Mounting BracketMB2 Mounting BracketMB1F Mounting BracketMB2F Mounting BracketMB3F Mounting BracketMB1V Mounting BracketMB2V Mounting BracketMB3V Mounting BracketCORG Gravity CoordinatorCB1 Carry Bar

Flush bolts are usually used to anchor the inactive leaf of a set of french windows or doors. They are usually mortised into the edge of the door or window, making them concealed and providing extra security.Handle set used on the active panel. This set will always have two cylinder holes in the backplates to accept a full cylinder. Hardware used solely for the active panel. Includes latch and deadbolt and is handle activated. When a door is referred to as ?active? it means it is the primary functioning door usually in a pair of French doors. This will be the door that opens first. Decorative center section of wood or other material that is attached to the inactive panel and serves as a jamb. Decorative plate which mounts to the face of the door with holes to accept the handle and cylinder. Screws that attach one backplate to the other. The screws enter through screw holes on the interior plate, travel through the door and attach directly to the exterior plate.

Available in a variety of lengths to accommodate different door thicknesses. Distance from the surface of the lock faceplate to the center of the handle hole. This distance establishes where the handle will be mounted to the face of the door. The HLS multipoint system uses a 35mm (1 3/8") or a standard 45mm (1 3/4") backset as well as 60mm (2.36) and 70mm (2.76) backset. The unit that mounts lengthwise through the door thickness and backplate. The thumb turn knob and key activate a cam which locks the deadbolt. Screw used to tighten cylinder into place. The screw enters through the faceplate and drive rail on the edge of the door and tightens into a threaded hole in the side of the cylinder. Square shaped bolt used on all gears to secure the door at the mid-point. Located directly below the latch, it comes in two different lengths; 14mm (0.55") and 25mm (1.00"). The vertical moving mechanism of multipoint hardware under the faceplate. The drive rail carries the motion from the gear to the multipoints to activate them.

This can be achieved through a single part or through multiple parts hooked together such as extensions and corner drives. where to buy shutter hingesThe drive rail is hidden by the faceplate.sliding barn door flat track hardware Handle set is usually "fixed" in place. car door lock repairs adelaideHandles serve only as pull handles and do not operate. door apartment for sale manilaUsually used on inactive panels where a mortise flush bolt has been used. wooden bifold doors australia

These sets have no cylinder holes in either backplate. A term used to describe the activating of the multipoint hardware. french door hardware flush boltWhen the multipoints have been activated into position, the system is said to be engaged. Routed groove in the edge of the door, usually centered, but may be offset to one side in which the drive rail and faceplate of the multipoint hardware are mounted. Sections of operating drive rail that can be attached to the gear to reach the needed height of a door. Flat piece of metal that covers the drive rail and multipoints along the entire length of the door sitting flush with the edge. The outer casing of a door which mounts directly into the rough opening of a wall. Main functioning body of multipoint hardware containing hub for handle operation and deadbolt (on active gear). Kit which includes handles, backplates and screws and may also include a cylinder.

Handle set used on the inactive panel. This set will have a cylinder hole on the inside plate only to accept a half cylinder. You may also use an active set on an inactive panel. Hardware used on the inactive panel, no latch or deadbolt. When a door is referred to as "inactive" it means it is the secondary functioning door in a pair of French doors. This door can only be opened after the ?active? panel has been opened. The catch for the door. The main body of the multipoint gear. Prevents locking points from accidentally firing and potentially damaging door trim. Edge pocket for lockcase or additional locking points. Any hardware containing a gearbox that requires pocket routing in the edge of a door in order to be mounted or installed. Any hardware that has multiple locking points which simultaneously lock into place through the action of a continuous travel drive rail activated by a handle. Type of finishing process in which parts are spray painted in a spray booth and then baked to cure the finish.

A UPVC or aluminum extrusion used in door manufacturing. The shape/style of each extrusion differs between each extruder and therefore requires different hardware--particularly hinges and strike plates. Refers to the distance from the center of the handle hole to the center of the cylinder hole. HLS swing door standard is PZ 92mm. Small cylindrical cam locking point that is connected to the drive rail and secures inside a strike plate by an upward and downward movement along the surface of the faceplate. Bullet shaped locking point that retracts flush inside the faceplate until engaged, at which point it deadbolts the door inside a strike plate. No upward or downward movement. This version requires additional mortising for the roundbolt lockcases. A support on the backside of the gear for the screws which helps prevent flexing or bending of the gear once installed in the edge of the door. Small screw located on the neck of the handle which is used to tighten handle into the spindle.

Arrow shaped locking point that retracts into the eurogroove until engaged, at which point it extends out and locks into strike plates in the head and sill of the door. A mortise lock consisting of a latch and deadbolt only. One or two-piece metal shaft used to mount the handles to the door. The two-piece has a groove that accepts the set screw in the handle. Available in different lengths to accommodate a variety of door thicknesses. Upright or vertical piece of the framework of a wood flush door. Plates that the locking points (roller, tongue, round bolt, deadbolt or latch) lock into. Different strike plates are required for different versions of locking points and profile designs. The horizontal botom portion of the door frame, also called the sill. Distance a deadbolt, tongue, roundbolt, etc. travel from beginning point to point of full extension. Triangular shaped locking point that retracts flush inside the faceplate until engaged, at which point it extends out to lock into a strike plate.