A bi-fold door stays in place thanks to the proper alignment of door pins and rollers. Both the top and bottom rollers run along a track. The bottom roller has a tendency to jump the track due to improper alignment. In turn, the top roller may fall out of the track following this misalignment. A pin is present at the top and bottom outside edge of each bi-fold door to hold the door in place. Adjustments of either the pins and rollers or a combination is required to maintain a properly working bi-fold door. Open and close the bi-fold door. Watch the roller on the top inside edge of the door to ensure it is centered in the upper track. Pull the roller down and center it between the track if it is misaligned. Let go of the roller and it will slide into the upper track. Open the closet door. Locate the pins at the top and bottom outside corner of the bi-fold door. Check to see if both pins are fully inserted in the pin bracket holes and not resting sideways on the bracket. Correct a crocked pin by pulling the pin toward the bi-fold door.

Center the pin in the hole and release. The pins should slide in the holes on a straight vertical axis. home depot door tintTighten the bolt in each of the pin brackets with an adjustable wrench to ensure they will not slide or move. personalized door mats bed bath and beyondSlide the door back and forth if required to position the pin. sliding door track cover lowesClose the bi-fold door. 4 door jeep wrangler for sale in michiganVisually inspect the gap between the outside edge of the bi-fold door and the vertical edge of the pinned side of the bi-fold door for a 1/16-inch gap. auto glass repair arlington va

Adjust the pin brackets if necessary to attain the proper gap. Lift the pin from the bracket. cavity sliding door frame sizesProp the bottom edge of the bi-fold door on a book. kitchen door hinge nzRemove the bolt in the bottom bracket. Slide the bottom bracket along the track the required distance to attain a 1/16-inch gap. Reinstall the bracket and the bottom pin. Pull up on the bottom roller on the inside edge of the bi-fold door to remove it from the track. Center the roller over the track and release. Open and close the bi-fold door to ensure it no longer jumps the track. Things You Will Need Adjustable wrench Tip References Home Tips: Bifold Door Repairs Suggest a Correction - TwitterFacebookLinkedInYouTube The UTS.60.Thermally Broken ULTRA Folding Door System Description:F FeaturesConfigurationsColorsHandlesThe UTS.60 folding door system is custom made to order with a large variety of options available.

System Overview: This system contains 15/16″polyamide thermal break bars. The top track, bottom track and side profiles form a closed frame. Together with the doors, having aluminum rebates and gaskets, all act in compression.Maximum Panel Height: Up to 120″ and up to 144″ with a true divider.Maximum Panel Width: Up to 42″.Panel Weight: Approximately 6 to 8 lbs/sqft changing with the height and width of the panels.Panel Capacity: The stainless steel carrier hinges are rated up to 450 lbs. per panel. The sealed bearing rollers allow for effortless operation even on the largest sizes.Number of Panels: Countless panel groups can be built. They slide along the tracks and are connected with special joints and seals.Profiles: Made of extruded aluminum with special ribs that ensure maximum hardness. Profile thickness is 2 3/8″.System Configurations Available: There are 26 operational door typologies and when in the open position they maximize 90% of the total rough opening. 90 degree corner is an option.

Swing doors may be integrated to provide an access point without having to move more than one panel.Running: Operates with either top hung or bottom running carriages along a single inline track.Folding: Inswing or Outswing.Glazing: Clear Low-E insulated is the standard. Various types of glass and other materials at a thickness of up to 1 1/8″ may be used. The glass is shimmed by means of accessories located in the corners of the doors and is externally adjustable at any time.Adjustments: Both sides of the frame are made up of 2 profiles, both of which have regulation points easily accessible from the outside, allowing for better installation and recovery due to seasonal temperature changes. Once door heights are set and locked, the mechanism will not self-adjust or loosen over time. Further head adjustments can be made at any time with a screwdriver.Accessories:Magnetic gaskets are used to ensure a weather-tight seal every time. Their extra thickness running up and down the edge of the panels are padded to ensure no fingers are left behind.

The multi-point locks engage into the top and bottom tracks for increased security.Wheel carriages have stainless steel sealed ball bearings with four delrin fiber reinforced laminated double sliding rollers, exclusively designed handles with ergonomic grips, stainless steel screws and pins, special hinge channels that keep the hinges in place, and 10mm hinge pins double gasketed on both sides of the panels.Track Options:The standard track is top hung/bottom guided and mounts directly to sub-floor to ensure the smoothest possible operation. Each set of quad rollers are capable of carrying 450 lbs and its adjustable header is 3/4″. This track has the best resistance to weather infiltration.The top running recessed track relieves stress on bottom track by distributing heavy panel weight to header. An optional drainage line could be installed.ADA compliant dual running recessed track is also an option. This track flush with the finished floor for a “barefoot” friendly area and a seamless transition from the interior to the exterior.

It is good for use in openings where weather infiltration is a concern, and in pass-through window configurations. An optional drainage line could be installed. Most Common ConfigurationsPanel widths up to 42″.Panel heights up to 120″and up to 144″ with a true divider.Inswing and outswing available.Each panel weights approximately 6 to 8 lbs per square foot. Standard ColorsOur entire product line is available in the following 25 standard colors. These colors cover the most popular choices, and are readily available at the standard price. All standard colors are verified AAMA 2604 Compliant with the option to upgrade to a verified AAMA 2605 Compliant powder coating finish for an additional charge.Bravado Cranberry      Olive Brown Almond Boxwood Taratone      Hale Navy      Black Anodized Silver      Tech White Pebble Gray Satin      Swiss Coffee      Green      Gray      Black Anodized Effect Craftsman Bronze Metallic Full Moon Silver      Traffic White Chestnut Brown Marley Bronze Brown Brown Coconut White      Dark Bronze      Clear Anodized Effect Standard BronzeCustom ColorsVirtually every color imaginable can be produced, along with a variety of finishes such as anodized

, kynar, metallic, translucent, flats, gloss, wrinkle and hammered. Give us a color sample to match or even an RAL* number, and we will produce your windows and/or doors in your own custom color (Available with an additional fee for color matching).All custom colors are verified AAMA 2604 Compliant with the option to upgrade to a verified AAMA 2605 Compliant powder coating finish for an additional charge.Color Disclaimer Due to the limitations of desktop scanners and the relative inconsistencies of various display monitors, the colors you see on your screen may not be a totally accurate reproduction of the actual product. We strive to make our colors as accurate as possible, but screen images are intended as a guide only and should not be regarded as absolutely correct.For exact color options, please for a sample.Handle OptionsUltra folding door systems are delivered standard with in-house manufactured Panda handles.Custom powder coating is available in a variety of AAMA 2604 and AAMA 2605 compliant colors.