Ferche Fire-Rated Wood Door Frames are used in a wide range of applications where the appearance of wood is essential. Below are some categories where you can specify Ferche Fire-Rated Wood Door Frames today. And, don't forget that Ferche is North America's leading hardwood moulding and door component manufacturer, so we can provide all of your non-rated frames, door components and trim, as well! Fire Rated Jamb Specs (PDF) Fire Rated Components Brochure (PDF) Fire Rated Parts Specs (PDF) Fire Rated Line Drawings (PDF) Learn more about Ferche Millwork's fire rated frames here. Architects - 3 Part Spec (PDF) Installation Instructions - Laminated Core 45-60-90 Minute (PDF) Installation Instructions - GP Gypsum 45-60-90 Minute (PDF) Installation Instructions - 20 Minute (PDF) Ferche 20 Minute Frame GP Gypsum Core FrameTracks and Springs Track & Spring Preparation Track & Spring Mounting General Specifications Track & Spring Preparation NOTE: Jambs, head framing and spring pads are not furnished by manufacturer.

Jambs must be flush and level around the entire opening and not have any fasteners past the face of the framing material. The jamb must be continuous and flush. Spring pad location (1 or more) depends on door size and number of springs used. sliding glass door adelaideContact factory for exact location. exterior door threshold typesIf pad is wood, use #2 or better southern yellow pine. hollow wood door hole repairDo not use wood labeled SPF. fingerprint door lock youtubeMinimum 2" x 6" jamb facing or 2-1/2" x 3/16" steel channel should be securely fastened to the building structure. auto glass repair summit il

Opening width is determined by jamb to jamb (not including stop molding). Opening height is determined by floor to bottom of header (not including stop molding). Verify required door sideroom for hardware. vintage door knob wine stoppersVerify required door headroom.sliding door hardware san diego Track & Spring Mounting Reverse Angle: Primarily used on steel and masonry jambs, but may be used on wood jambs or optional wood covered masonry jambs. The door will overlap 1" on both sides and will close and seal up against the optional vinyl molding. Thus door needs to be 2" wider than finished opening width. Bracket Mount: Used exclusively for wood or wood covered masonry jambs. Doors will close and seal up against the wood or vinyl stop molding. Typically the door size equals finished opening.

Applied stop molding will reduce the true opening width by about 1". Continuous Angle: Used on larger doors on wood or wood covered masonry jambs. Applied stop molding will reduce the true opening width by about 1". General Specifications Tracks: Track is 2" or 3" depending on size and preference. Vertical Tracks: Shall be minimum of 16-gauge galvanized steel tapered and mounted to provide wedge-shaped sealing action (2" track or 3" track, depending on door size). Horizontal Tracks: To be minimum 14-gauge galvanized steel, reinforced with minimum 13-gauge galvanized steel angles required. 3" track to be 12-gauge. All track, vertical mounting angles and brackets will be ASTM A-526 commercial quality steel minimum 16-gauge thickness, G-40 minimum hot dipped galvanized. Horizontal track will be reinforced with continuous angle of adequate length and gauge to prevent deflection. Spring Counterbalance: Door assembly to be operated by a torsion spring counterbalance mechanism, with a helically wound, oil tempered torsion spring mounted on a steel shaft.

Cable drums are die cast aluminum with high strength galvanized aircraft cable with a minimum 7:1 safety factor. Shall be factory calibrated springs to match site specifications. Shall provide a minimum of 10,000 cycles. 25,000, 50,000, and 100,000 cycle springs are available. Shaft: Steel tube will be supplied depending on door size and springing, otherwise solid shaft will be supplied. Solid shaft, where tubing is standard, can be specified. All tubing/shafting will have a minimum of 3 load bearing plates side/spring anchors. Solid shaft is strongly recommended for Jackshaft operators. Clopay's Track Specs are available for download in PDF format. Adobe Acrobat Reader 5.0 or better is required.If you cannot open DWG or DXF files: Right click on the DWG or DXF icon then "Save File As" to a file on your computer then open in your CAD program. DWG files can be downloaded and opened in most CAD systems. Download a free DXF/DWG viewer. Low Headroom-Rear Mount Track Low Headroom-Front Mount Track

High Lift Follow-the-Roof Track Track Drawings & Specifications Standard Track Follow the Roof Track Low Headroom–Rear Mount Track Low Headroom–Front Mount TrackModel 418 Alloy Steel Invisible Hinge Model 418 Alloy Steel Invisible Hinge SOSS® Invisible Hinge model #418 is for use in wood or metal applications. This full size door style hinge will provide superior appearance and durability. Our Hinges are found in many applications where flush fit, compact size and smooth operation are necessary features. SOSS® Invisible Hinges open a full 180° and are a single action hinge. The Underwriters Laboratories labeled the model #418 SOSS® Invisible Hinge can be used on hollow metal , sheet metal, tin clad, and steel composite swinging type fire doors and frames rated up to and including 3 hours. They can also be used on wood core doors and frames rated up to 20 minutes.Additionally, they can be used on wood/plastic composite doors and frames constructed with Georgia Pacific FS 1 or FS 2 banding for a rating up to and including 90 minutes.