How to Replace Rollers in Aluminum Sliding Glass Doors How to Replace Rollers in Aluminum Sliding Glass Doors *Note: This is a general article that can be used to replace the rollers in most aluminum sliding glass doors without having to remove the sliding panel from the door frame. Depending on door and roller, process may differ slightly. *Note 2: Most aluminum sliding glass doors use single-assembly rollers. Most are steel, although some use nylon. The best way to figure out which rollers you need is to use steps 1-6 to remove your rollers and buy replacements that match. Unscrew and remove both aluminum stiles of moving panel. One person lift up door while other slides bottom rail over so roller screw can be accessed. Unscrew and remove roller. Repeat to other side, again picking up glass and sliding bottom rail over so roller screw can be accessed. Put door back together. Adjust rollers so door sits squarely in frame. To access and remove rollers on sliding panel, unscrew stiles (side components of aluminum frame).

Once unscrewed at top and bottom, gently knock a block of wood against the frame with a hammer as shown in the picture below. Do this at top and bottom until stile comes off--should be left with glass edge in rubber boot. *Note: if rubber boot comes off, it easily slides back on. In the project depictured in the photographs, the boot came off; we left it off and put it back in place before we re-installed the stiles. Repeat on other side. Only rails (top and bottom components of aluminum panel frame) should remain on sliding panel. Place wood block (block must be 3/4" wide or smaller so as not to hit glass) against bottom rail and gently knock with a hammer to nudge it along the track, independent of glass. Goal is to expse screw hole on top of bottom rail so roller can be removed. Rail should only need to be moved a few inches. *Note: When moving bottom rail, have partner gently lift panel (easy to do with large suction cup) to take weight off rail. Another picture of this process is shown after step 9.

Using screwdriver, remove screw in top of rail holding roller in place. Using a hook tool (we used a balance hook), a bent hanger, or needle-nosed pliers, grip underside of roller housing or roller adjustment screw through side of door and pull out.double glazed doors northern ireland Before installing new rollers, adjust them to lowest possible position (so panel is low in door, not raised up). average cost to refinish front doorRollers adjust via adjustment screw on side of roller body.upvc back door second hand Install new roller by inserting it into side of bottom rail, wheel-down, and sliding it into panel until screw hole in roller is lined up with screw hole in panel. glass shower doors edinburgh

Screw in place through top of bottom rail. Lifting panel again, slide bottom rail back in opposite direction and follow steps 6-8 on other side. Lift glass panel again and slide bottom rail back into original position, centered on glass panel.wood stoves for sale kansas city Gently replace stiles, one side at a time. bi fold timber doors australiaUse handle of hammer or hammer a block of wood (working up and down entire side of panel) to fit stiles back in place correctly. Do not use head of hammer directly on aluminum to fit back in place.Direct contact of hammer head on aluminum frame will dent frame. Re-install screws at top and bottom of each stile. Adjust rollers for corrct height. Use a pry bar to lift panel, insert screwdriver in adjustment hole and turn screw to raise and lower panel within door frame.

Adjust both sides equally. Check operation of door, making sure lock functions correctly (lock on sliding panel lines up with strike on frame). Adjust until door is in correct position. Products Related To This Article:Customer Questions & Comments See all discussions You are a: Quick Learner Handy Person Contractor Home Owner Distributor Friend Architect Landlord Professional Purchasing Agent Realtor Located in: Email: Subject: Post: Images: + add another image + add another image + add another image + add another image Plaza Doors were designed for ease of operation, optimum security, and maximum durability. The ease of operation is a result of our silent heavy duty roller assemblies and heavy extruded frame sections. The stainless steel Adams Rite Hook-bolt deadlock with full height adjustment offers trouble-free operation and security. Durability is ensured by using the finest grade of aluminum as well as non-corrosive finished materials in our production. We chose a narrow profile for our frames to allow for the least obstructed views.

We are a custom manufacturer, not limited to a set number of configurations or product sizes. Noted for innovation we build to your required specifications. Whatever is needed for a successful retrofit of an existing building requiring an upgrade of its sliding doors, we do everything possible to make sure the door is correct. One of the most important components of a sliding glass door is the roller assembly. This assembly, designed by IIBP, is made of 6061-T6 structural grade aluminum alloy with stainless steel axle pins, sealed ball bearings, and adjusting screw. The large diameter wheel is molded of high density Derlin compound for durability. Derlin is a naturally lubricating material and does not wear away the heavy anodized finish applied to the track. The stainless steel bearing is protected from dust and dirt with Teflon dust shields. It all adds up to a very quiet, easy-rolling, corrosion resistant door. The single roller assembly is part of the standard quality package furnished on our Sentry, Atlas, and screen door panels.

The large diameter roller tire makes these units roll quietly and with little effort. The tandem roller assembly is included as standard hardware on our Titan Series sliding door units. They can be retrofitted to any existing Plaza Sliding Glass Door regardless of the series. The use of two wheels per roller means the mechanical advantage of the large tires has been doubled to provide the easiest, smoothest, and quietest rolling Titan door panels, regardless of their size. Built-in "Weep" Drainage System Water drainage is important in areas where constant rain is a part of everyday life. To keep rain water from findings its way inside, Plaza Door uses a series of watertight discharge pans hidden underneath the track. The force of the water rolling off of the doors pushes the water into corresponding "weep" holes that allow water to find its way off of the track and away from the door sill. Our special "Titan Hi Rise" surface draining track may be utilized for optimum performance during extreme weather and high wind conditions.

Four Point Weather Sealing Double Pile & Bulb Vinyl The Pile or "fuzz" weather stripping plays the critical role of keeping insects from finding their way inside. The bulb vinyl weather stripping is important because it blocks wind and rain water from entering the interior. Plaza Door integrates this industry standard of weather sealing twice at every jamb, door astragal, and interlock meeting condition. Having this feature helps eliminate the " whistling" or "howling" many sliding glass doors produce during extreme windy conditions. One of the features of the Plaza Sliding Door System that separates our sliding door units from other manufacturers is our sliding screen panel. When design features of the Plaza Sliding System were being established, it was determined that the screen panel for a sliding door unit was equally important as any other part of the unit. To satisfy that decision, the Plaza screen panel has been designed with the same care as the door panel and frame components... with the same profile, including extrusion wall thickness equal to the door sections.