Few things make a bedroom seem shabbier than a beat-up sliding closet door that's hanging crooked or that won't open and close smoothly. Inexpensive closet doors often are installed to cut down on building costs, but doors made of low-quality materials and hung with inexpensive hardware can lose their alignment and become difficult to operate. And they sometimes don't wear very well, so they can become stained and scratched. A reasonably handy person can correct most minor closet-door problems fairly easily. And if the door is too far gone or too ugly to save, replacing a closet door is also a simple project.Closet doors come in three basic styles: sliding (sometimes called bypass), bifold and swinging-hinge doors. Swinging-hinge doors are like the other interior doors in your home, but bifold and sliding doors are hung from tracks and might need extra attention.The side of a bifold door is attached to the door jamb with hinges or pins in brackets. The side of the door opposite the hinges is suspended from a sliding mechanism that moves along a track.

Sometimes the slides stick. If the sliding mechanism contains a wheel, a little light oil in the works might improve the operation. If there is no wheel, try rubbing a little candle wax on the track.Sliding closet doors, which are used in pairs, are not attached at their sides but glide along overhead tracks. They can become sticky, too, but they almost always have wheels that can be oiled.Sliding doors usually have at least one floor bracket that keeps the bottoms of the doors in line with their tops.A common problem with sliding doors is misalignment. If the doors are higher on one side than the other, or if they are hung too low, they might drag on the floor or snag at the floor bracket. If they're hung too high, they can swing out of the floor bracket and come completely out of the track.The alignment of sliding doors usually can be adjusted without removing the doors.Step inside the closet and look for the brackets that attach the sliding wheels to the top of the door. The bracket should be held in place with screws set in curving slots.

With a partner holding the door, loosen the screws in the curving slots but don't unscrew them completely. Move the bracket up or down as needed and partially retighten the screws. Test the door to see that it slides properly before retightening the screws.Replacement brackets and wheels are available at home-improvement stores. Replacement components run from about $2 for simple wheel assemblies to $20 for new brackets and tracks.Some closet doors are made of a lightweight wood called lauan. Such doors usually have a framework of pine or other wood around the edges, and the center part of the door is hollow.The wood in the doors sometimes deteriorates, and screws can become loose, making hinges and brackets rattle.When a screw refuses to tighten in deteriorated wood, you have to dismantle and remove the hinge or bracket and plug the old screw hole.Put a little wood glue on a wooden golf tee and tap the tee into the screw hole. Allow the glue to dry a while, preferably overnight, and then cut off the extra part of the tee with a utility knife.

Closet-door sizes are standardized (24 by 80 inches, 36 by 80 inches, for example), and it should be easy to find replacement doors where lumber and building supplies are sold. car glass repair newcastleMeasure your existing doors and look for replacements with the same dimensions.shower door seal for p shaped bathTo remove sliding doors, unscrew the floor bracket and slide it from under the doors. electric garage doors melbourneSwing the bottom of the door up and lift the body of the door to disengage the sliding wheel from the track. windows and doors rancho cucamonga

If the track and wheels are in good shape, you can attach the wheels to the new doors and keep the old track.Bifold doors are removed by disconnecting the hinges. The slide holding the top of the door should then slide out of the track.ipad 2 screen replacement cnetBifold doors come in a variety of styles, from plain flat panels to paneled hardwoods or full-length mirrors. sliding closet door lock 2-packPrices start at about $35 for an unfinished, 36-inch-wide door and go to about $150.Sliding doors tend to be a bit cheaper, with 36-inch lauan panels going for about $25 and other woods mostly in the $35 to $90 range.car window repair tucker gaOften the hardware to hang a door comes with it, but some doors are sold as plain panels.

The hardware to hang a pair of 36-inch sliding panels or bifold doors in a 72-inch-wide closet opening costs about $20. Therapists see no developmental benefits from seats`Jop' would be a 4-ever pick for the BullsDark meaning of bubble-gum Pumped Up Kicks is tough to chew Barkley Fined, Suspended For Spitting IncidentToo cold for car wash? Motormouth answers your questionsDouble Murder: A Family Affair?Be sure to scroll down... there may be more than one question on this page! Two 4 foot doors? You do have a problem… but I have the solution. One option would be to mount four pairs of 2-foot bifolding doors. Terminologically speaking, this means a total of eight one foot doors, hinged inBecause the "hinge" side of bifolding doors consists of a floor-mounted pivot and a top-mounted track, you can install multiple 4 foot tracks side by side with no need for a vertical wood support at either end. center door pairs would hinge in the middle of the 8 foot frame, giving the

appearance of two separate four foot closets when open. If you really want the total 8 foot opening to be absolutely obstruction free (except for the thickness of the doors on either side of the frame), use bifolding hardware with four standard 2' wide doors. You can purchase a separate bifolding hardware kit, which includes hinges, track, and all associatedHollow-core doors would be the best choice, since the weight will be more easily manageable by standard bifolding hardware. If you have a thing for heavy solid doors, mirrored doors or doors with glass panels you might find that the weight will overload the bifolding track/pivotNo way to know until you try it, though. Then, you would need to use butt hinges… either standard door hinges or special low-clearance hinges that require no mortising… to install the doors to the frame instead of using theObviously, this is a more labor and skill-intensive job, so trying the bifolding method first might be the way to

The hardware is not that expensive. You could still continue to use the top track to guide the "leading" door of each pair so it does not swing out from the frame, keeping the bifolding function but with additional strength. I can give you a number of options... choose the one that best suits your needs and abilities. One would be to use solid doors instead of hollow doors. 6-panel moulded doors are available with a solid core allowing you to cut a little more from each edge without having the doorsJust be sure to cut the same amount from all 4 vertical edges so the doors look balanced. Most prehung bifold door "sets" come with hollow doors, so you will have to order raw solid doors and purchase the bifold hardware separately. Another option would be to use three doors instead of two... you would have to use standard hinges on the "outside" door since the standard bifold hinges have a support tab that is unattractive on the outside of the door.