Video Playback Not Supported Installing bifold doors on a closet or other opening is a fairly simple DIY project. Depending on the width of the opening, one or two pairs of bifold doors may be needed. To install bifold doors: Take down any existing sliding or hinged doors. Measure the width and height of the opening and buy bifold doors to fit. If needed, trim the outer edges of the bifold doors slightly to fit the opening using a plane or circular saw with fence. Install the bifold door track on the top of the door casing. Attach the bifold door brackets to the bottom of the door casing. Attach the guide and bracket pins in the predrilled holes in the top and bottom of the bifold doors. Set the bifold doors in the top track and bottom brackets. Adjust the top and bottom pivot points so there is an even gap between the bifold doors and side door casings, and the doors open and close properly Watch this video to find out more. How to Hang Bifold Closet Doors (video/article)

How to Reverse and Rehang Bifold Doors (article) How to Install Pocket Doors (article) The first step to installing a bifold door is attaching the track to the header, or top, of the door frame. Next, you’ll need to install the lower pivot points on the floor directly below the track on either side of the opening. price of liftmaster garage door openerYou’ll want to use a plumb bob to get the location just right.best way to restain a door The door then sets into the lower pivot point and snaps into the upper pivot in the track. sausage dog door stop patternThe upper pivot can be adjusted along the track until the door is aligned properly.external hardwood doors cornwall

Videos You May Like How to Reverse and Rehang Bifold Doors Hang Bifold Closet DoorsHow to Maintain and Fix Sliding Doors The two types of doors that are easiest to open don’t have hinges at all; instead, they slide on tracks. Sliding-glass doors are a popular feature in rooms with decks or patios because their full-length glass panels open the room visually to the great outdoors while providing easy access to the outside. garage door suppliers norfolkInterior sliding doors are frequently used for closets and pantries, and sometimes to conceal water heaters and furnaces. auto glass repair sugar land texasYou can remove sliding-door panels easily to gain complete access to what’s behind them. jbl car door speakers india price list

Follow simple repairs and maintenance procedures to keep your sliding doors on track. Patio doors slide horizontally — or at least they’re supposed to. All too often, these big, pesky contraptions stubbornly resist opening, and getting outside becomes about as easy as dragging a refrigerator through a sandbox. The most common cause of a sticking patio door is debris in the lower track. This channel easily becomes clogged with dirt and leaves because people and pets walk over it whenever they go in or out. Each time you vacuum your floors, use a small brush attachment or cordless vacuum to clean the sliding-door tracks. Apply a lubricant to both upper and lower tracks to keep the door hardware clean and operating freely. In addition to cleaning and lubricating sliding-door tracks, you want to lubricate the door lock. The best way to lubricate any lock is to disassemble it and use an aerosol lubricant to flush away grime and coat the moving parts of the lock. Sometimes, patio doors become hard to open even when the track is clean.

In these cases, the problem is usually that the rollers at the bottom of the door have started to rub against the track. The rollers at the top can also wear down, lowering the bottom of the door so that it rubs on the track. Most sliding doors have a mechanism called an adjusting screw located at the bottom of the door ends. Turning this screw raises or lowers the roller. Give the screw a clockwise turn and test to see whether the door slides easier. If the door becomes even harder to open, turn the screw in the opposite direction. After a bit of adjustment, the door should roll easily without rubbing on the bottom track. Sliding closet doors operate on rollers that are positioned in tracks at the top jamb and floor, allowing the doors to bypass each other in the tracks. Because sliding doors don’t fold out the way bifold doors do, they allow access to only half the width of the opening at a time. To clean and lubricate the hardware of a sliding closet door, use a stiff brush, a toothbrush, or a hand vacuum to clean dust from the tracks.

Use an aerosol lubricant to lubricate all the door rollers. If the rollers are damaged, install replacement rollers (available at home centers). If the door doesn’t hang level, leaving an uneven gap between the door and door frame, look for an adjustable mounting screw at the inside top of each door. Use a screwdriver to adjust the mounting screw and even out the door.Adjust Bi-fold Doors on the Closet Bi-fold doors move on rollers sliding at the upper track, and, pivots at the outer top and bottom. There may be door aligners at the center where the two doors meet and, a spring bumper at the center track that absorbs the closing. To adjust the vertical position on the doors, it is done by a combination of two ways: At the bottom pivot; this is done by opening a half set of doors. Lift the pivot door slightly at the outer base and move the bottom position in its bracket - in the direction of the center or toward the wall. Note that some of the lower pivot brackets have clip-ring inserts used for adjusting - if your brackets have these be careful,

the plastic clips break off. Also, if central aligners are being installed, these should be put on last - after the doors are To adjust the top pivot as needed, tape measure how much distance the door should be shifted from below. Untighten the top pivot screw and slide the pivot bracket into position, level with the pivot below, steadying the door and this may take a secondOnce into position, re-tighen the screw. Also, when working on the interior section, a flashlight may be needed for finding the If you need more access to the upper bracket, depending on your design, you might have to remove the whole double door section by depressing the upper pivot which is spring loaded, along with the accompanying roller. Transfer the lower door-edge to wall distance, to the top. As the door is adjusted, there must be a turning void at the door edge. The doors should have about the same distances for both outer door edges, left and right, and a small gap at the center, that does not not bind the two when closed.

To adjust the door height alone, with the doors already in level, simply raise or lower the doors at the lower pivots by rotating the adjusting nut(s). As the doors wear, and especially for masonite doors, some have a tendency to begin wobbling when they swing. If your doors are unstable at the pivot, and the brackets are secure, pull the door sections completely off and check the pivot mounts in the ends. Frequently this means replacing the doors, or, replacing the internal door plug(s). Then installing new pivots. To replace the door plug - typically the plug width is 1 1/8" which is not dimensional stock so this will have to be ripped. First remove the current plug (pull on pre-drilled screws). Then sand the inside surfaces, and apply wood glue before applying pressure with a pair of wood clamps. Wipe of the excess and let dry. Once cured, seal both top and bottom ends, and let dry. Drill and place new pivot barrels and reinstall the doors in position.