It looks like nothing was found at this location. Maybe try a search?Secure your garage by changing the door code from time to time. If you think someone knows the code to open your garage door or your remote has been stolen, it is time to change the code on your garage door opener. Newer garage door openers have a keypad in addition to the remote, which makes it slightly easier to change the code. If you have an older garage door that is only operated by a remote, you must physically move the switches inside the remote and door opener to change the code. Place a ladder beneath the garage door’s motor unit to reach the unit. Press the learn button located on the side of the motor and hold it down. Release the button when the light beside it goes out to remove the old code from its memory. Push the learn button on the motor again, so its light comes on again. Enter the desired code on your keypad on the garage wall. The motor unit’s light blinks to indicate that the new code has been accepted.

Press the learn button on the motor once more, so the light on the motor lights up again. Press a button on your remote. The motor unit’s light blinks to indicate the remote has been programmed with the new code. Repeat this step to program all other remotes. Take the cover off of the garage door’s remote control to expose the switches inside the remote. Repeat to change the code in all additional remotes. Move the switches inside the remote to change the code. Replace the cover on the remote control. Place a ladder beneath the garage door’s motor unit. Move the switches on the motor to change the code to match the code in the remote control. /Getty Images Suggest a CorrectionHow do I erase the remote control from the garage door opener's memory? There are a few instances that the memory of your opener would need to be erased. NOTE: Erasing the memory will remove ALL remote controls and keyless entry codes from the garage door opener. Begin by locating the LEARN button on the back or side of the motor unit;

generally this is on the same side as the antenna wire. You may need to remove a light lens cover or open a control panel to gain access. The LEARN button may be green, orange, red, purple or yellow, and will have a small LED next to it. Erase all remote controls and keyless entries Units with a green, orange, red, purple or yellow LEARN button: Erase all remote controls, keyless entries and MyQ® devices from the garage door openersliding patio doors hurricane To reprogram a remote or keyless entry, go togarage door murals for christmas How do I program my remote control? garage doors plymouth michigan How do I program the keyless entry? frameless shower doors rochester ny

Click here to see a video about how to erase the programming of a remote control. See Also: How to erase the memory of your garage door opener youtube video. Answers others found helpful Video - Erase the remote controls from memory How to program a remote control How to find the "Learn" button on my garage door opener How to program accessories to your Internet Connectivity DeviceThe Linear GoControl Garage Door Opener (GD00Z-4) lets you remotely open and close almost any sectional garage door. garage door opener noise isolationWith both audible and visual warnings that trigger prior to remotely activated door movement, the GD00Z-4 meets UL 325-2010 safety requirements. genie garage door opener home linkThe GD00Z-4 also includes a wireless tilt sensor that attaches to the inside of the garage door and reports whether it is "open" or "closed."

This Z-Wave garage door opener provides peace of mind, convenience, security, and safety. Connect the GD00Z-4 with SmartThings to open or close your garage door from anywhere—perfect for allowing entry for a handyman, or for closing the door if you forgot to. You can also set up automations to open or close the garage door as you arrive and leave home. The GD00Z-4 will act as a Z-Wave repeater for other Z-Wave devices on your SmartThings network. 1. Install the tilt sensor The GD00Z-4 includes a wireless tilt sensor that attaches to the inside of the garage door. The tilt sensor reports “open” or “closed” status to SmartThings. Consult the GD00Z-4 installation instructions, which can be downloaded from the link at the bottom of this article, to install the tilt sensor. 2. Pair the GD00Z-4 with the SmartThings Hub First, connect the GD00Z-4’s power cord and plug in the device within 10 feet of the SmartThings Hub. Next, in the SmartThings mobile app:

3. Mount and connect the garage door opener Consult the GD00Z-4 installation instructions, which can be downloaded from the link at the bottom of this article, to mount the GD00Z-4 and to connect its wires. If you need help installing the GD00Z-4, contact a certified electrician. If the GD00Z-4 was not discovered, you may need to reset, or “exclude,” the device before it can successfully connect with the SmartThings Hub. To do this in the SmartThings mobile app: After the app indicates that the device was successfully removed from SmartThings, follow the first set of instructions above to connect the Linear GoControl Garage Door Opener. With the Linear GoControl Garage Door Opener (GD00Z-4) and a simple Routine, you can configure your garage door to open and close automatically based on activity, time of day, or other events. From the SmartThings mobile app: Depending on how you configured the Routine, the garage door will automatically open or close when certain events occur.