​​Wireless Keypad Programming Instructions Keypad Model OWK-BX and Model OKP-BX Just like our garage doors and openers, our support is the best in the business. Some say that our support puts the “genuine” in our motto, “The Genuine. The Original.” because we truly care about our customers and do what i​t takes to make sure you are satisfied with your Overhead Door products. View the wireless programming instructions by selecting your model. Should you need additional information about installing or programming your garage door opener or remote, use our Service & Support to locate a representative in your area to assist you or call our customer service at 800-929-3667. ​​​​​​​​​​​​​​​​​​​​​​​​​​​​​​​​​​ Select a model to view the programming instructions for that particular wireless keypad.How do I add, program or change a Keyless Entry PIN? Your keyless entry can be programmed to activate many devices including: garage door openers (GDO), gate operators, commercial door openers and external wired-in receivers.

Program using the Learn Button Locate the Learn button. Garage door opener: Located on the same side the antenna hangs from, you may have to remove the light lens. The Learn button may be green, orange, red, purple, or yellow with a small LED next to it. Gate operator or commercial door opener: Located on the control or logic board, with a small LED next to it. MyQ Control Panel: Lift the push bar and locate the learn button.garage door opener chip Press and release the learn button.garage door hardware calgary If you have a MyQ Control Panel, press the Learn button twice.garage door fitted essex NOTE: If programming to an 8500, remember that programming is done through the 888LM wall control, not the yellow learn button on the unit. closed door sales perth wa

For more information, see KB 8500 - Remote control or keyless entry will not program. Within 30 seconds, enter a 4 digit Personal Identification Number (PIN) on the keypad and press ENTER. The LED indicator light will turn off or the operator lights will blink indicating programming was completed successfully. Wait 10 seconds to test out your PIN. To test, enter your 4 digit PIN and then ENTER. The operator or opener should activate. If not, repeat steps 2 and 3. Program to an external wired-in receiver Once you have located the receiver, follow these steps for programming. Remove the cover of the receiver. Depending on the model, the cover may wrap around the receiver or the face plate may need to be removed using a flat head screw driver. We recommend downloading the instruction manual for better assistance on how to remove the cover to access the program button. Locate the learn button. This is usually a small radio button with an LED next to the button.

Press and release the learn button. Within 30 seconds, enter a 4 digit PIN number on the keypad and press ENTER. To test, enter your 4 digit PIN and then ENTER. The operator or opneer should activate. If not, repeat steps 3 and 4. Program to a garage door opener using the Multi-Function Door Control NOTE: This method requires two people if the Keyless Entry is already mounted outside the garage. Enter a 4 digit PIN of your choice on the keypad, then press and hold ENTER. While holding the ENTER button, press and hold the LIGHT button on the Multi-Function Door Control. Continue holding the ENTER and LIGHT buttons while you press the push bar on the Multi-Function Door Control. All three buttons are being held. Release the buttons when the motor unit lights blink. This is an indication the programming was done successfully. If light bulbs are not installed, two clicks will be heard. If the existing PIN is known, it may be changed by one person without using a ladder.

Enter the existing 4 digit PIN, then press and hold the # button. The opener lights will blink twice. Release the # button. Press the new 4-digit PIN you have chosen, then press ENTER. The motor unit lights will blink once when the new PIN has been changed successfully. Wait 10 seconds and test by pressing the new PIN then ENTER. The opener will activate. Set a Temporary PIN You may authorize access by visitors or service people with a temporary 4 digit PIN. After a programmed number of hours or number of accesses, this temporary PIN expires and will no longer open the door. It can be used to close the door even after it has expired. Press the main 4 digit PIN then press and hold the * button. The opener light will blink three times. Do not use a previous temporary PIN for this step. Enter a temporary 4 digit PIN, then press ENTER. The opener light will blink four times. Set a number of hours or times this temporary PIN will work. For hours the temporary PIN will work, press a number up to 255 then press *.

For times the temporary PIN will work, press a number up to 255 then press #. The opener light will blink once when the temporary PIN has been programmed successfully. Wait 10 second then test by pressing the 4 digit temporary PIN and ENTER. The door should move. If the temporary PIN was set to a certain number of openings, remember that the test has used up one opening. To clear the temporary PIN, repeat steps 1-3 and setting the number of hours or times to 0 in step 3. Setting up the One Button Close feature The opener can be closed by pressing only the ENTER button if the one button close feature has been activated. This feature has been activated at the factory. To activate or deactivate this feature press and hold buttons 1 and 9 for 10 seconds. Click here to see a video about how to program a keyless entry to a garage door. Answers others found helpful How to program a remote control Video: Program Keyless Entry The button on the wall works, why won't my wireless keyless entry work?