View all items > Door Kick & Push Plates Door Knobs & Levers View all 3 items > View all 5 items > Door Sweeps & Seals Lockset Reinforcement & Trim Plates Door Hardware from True ValueBefore family, friends, and loved ones enter your home, the first impression is made at your entrance. While it's easy to bypass landscapes, walkways, and other d�cor without notice, guests come face-to-face with your door hardware. This makes it important to select door products that are not only secure, but also complement the theme of your home, lawn, and gardens. True Value Hardware Stores help you accomplish those goals with stylish door knockers, secure door hardware, and many other accessories for turning your entryway into a focal point.The local True Value experts in your area understand your needs as a homeowner. Your door hardware should be a source of comfort and pride. With charming door knockers, stops, and door pulls, help ensure the value of your home is maximized.

Meet the True Value staff today, and let them guide you towards the right products and techniques for making the most of these quality entryway accessories. True Value does more than give you the tools for the job - we can also show you how to get results. today, and browse our project library for helpful advice on maintaining your front door, installing a door bell, and many other ways to invite quality into your home improvement plans!bi fold doors maximum width For finish carpenters, fine-tuning the fit of a new interior door offers plenty of bang for the buck. garage door sales kijijiThere’s a lot of easy gratification for little effort. schlage door hardware images

The final fit mostly involves door-hinge adjustment after the painters have finished. First, I check that the door is swinging properly on its hinges. If the hinge leaf fastened to the door is not set fully in the mortise because of paint, plaster, tape, or misalignment, the hinges will bind. This might cause the door to creak or to spring back from a closed position. If the mortise in the jamb is set too close to the stop or if the leaf on the door is not set far enough across the width, the door will bind against the stop. garage door parts murrietaIf this is the case, you will probably see telltale signs of scraped paint on the door where it rubs.home depot andersen entry doors When adjusting hinges, I often have to adjust the location of screw holes. garage door repairs leeds

Rather than struggle with a hole in the wrong spot, I simply tap in a plug and drill the hole where I want it. After I get the door swinging properly, I adjust the hinges so that there is a consistent gap between the door and the jamb. When making corrections to the gap or any adjustments to the door, I make incremental changes. Often, going forward by small degrees is easier than going back by any amount.garage door repair fullerton Secure the door with a long screw. Sometimes a door sags away from the hinge-side framing. To prevent this, I replace the short center screw of the top hinge with a 3-in. screw driven into the framing. Sinking this screw often changes the gap at the top and the opposite side of the door. Fine-tune the mortise for a good fit. A hinge leaf that stands proud of the jamb face can prevent a door from operating properly. Remove the screws to reveal the mortise.

If the hinge leaf and the mortise were not aligned so that the hinge leaf fully seated in the mortise when the screws were driven, there will be a compression mark from the hinge. With a utility knife, carefully cut along this line to expand the mortise. Use a sharp chisel to remove the wood waste and to clear any paint, tape, or wood debris that might keep the hinge from seating fully in the mortise; then reattach the hinge. Centering a drill bit in a hinge hole without a self-centering bit is not impossible—but it takes a lot more time. Selfcentering bits fit most hinge holes. The bit’s shank is chucked in a drill, and the cutting end is encased in a sleeve with a beveled tip that centers it in the hinge hole. As the bit is pressed to the wood, the sleeve retracts, allowing the hole to be bored while keeping the bit centered. Self-centering bits come in sizes to fit cabinet and full-size door hinges. You can buy them at home centers or online for less than $15. Open the hinge-side gap by spreading the hinges.

I’ve seen shims used behind the hinge leaf to adjust the gap, but bending the hinge takes less time. I can widen the gap in small increments. Remember that when the gap is adjusted on one side, it affects the gap on the other side as well. Place the butt end of a nailset between the hinge leaves up against the pin eyelet, or hinge knuckle. When the door is pulled toward the closed position, the nailset spreads the leaves and widens the gap. This technique puts a lot of force on the hinge, so go slowly to avoid damaging the hinge or bending it too far. Close the hinge-side gap by bending the knuckles. Set an open-ended adjustable wrench, also called a crescent wrench, just larger than the size of the hinge knuckle. Remove the hinge pin, and bend the door-side knuckles toward the door handle. This will close the gap. A difference of 1/16 in. is easy to notice. Correct offset screw holes. Sometimes, the mortise is in the right place, but the hinge wasn‘t set properly at the factory.