For some reason, the interior handles on Toyota Corollas ALWAYS ALWAYS ALWAYS crack. If you are sick and  tired of rolling your window down to get out of your car, this instructable is for you. All you will need: A new handle from Ebay This will cost you less than 10 dollars and talk less than 10 min.Step 1: Remove the Broken HandleShow All Items« PreviousNext »View All Steps DownloadVarious screws are removed and then the door panel is pried away. Electrical connectors are disconnected to separate the panel from the door. If you pull on the left door handle on your Toyota Camry and nothing happens, it's time to replace it with a new one. Replacing the door handle is a fairly easy but time-consuming task. Allow about five hours for its completion. The process for replacing the door handle is similar for both front and rear doors on most Toyota Camry models. For more detailed instructions pertaining to the specific year in which your vehicle was made, refer to the factory service manual.

Start with the window fully up. With a Phillips screwdriver, remove the two screws under the inside edge of the door, the two screws under the door handle, the screw underneath the light, and the screw underneath the mesh cover in the middle of the door. Press the two pins on the outer edge of the door with a flathead screwdriver. Pull the loosened pins out of the door. Remove the trim around the interior door handle. Wrap the end of a flathead screwdriver with electrical tape. Insert it between the pull handle and the trim around the interior door handle, and press down. At the same time, pull on the outer edge of the trim at the same end until the clasp that holds it comes loose. Keep prying toward the other end until all of the trim is loose. Pull the door handle, as if you are opening the door, and slide the trim off. Slide the flathead screwdriver or your pry bar around the bottom edge of the door panel. At the bottom, the panel is held on by plastic clips that will pop loose.

At the top of the door, the panel fits into the window groove. Gently lift the panel up and off. The panel will still be connected to the car door by a few wires. Set it down carefully. Peel the plastic liner away from the left side of the door. Using your straight-handled ratchet and 10 mm socket attachment, loosen the three bolts on the inside of the door that hold the handle in place. Finish unscrewing the bolts and catch them with your hand. Wiggle the door handle to loosen the final bolt and rod that hold the handle and door key lock/unlock switch. Flip up the plastic clip that keeps the rod in place, then remove the bolt and rod from the outside with your hand. Fit the new door handle into place. Using the ratchet tool, screw the three bolts that anchor it back into place. Insert the rod in its hole, and flip the plastic clip down over it. Use your screwdriver to mimic the bar that engages the closed door, and test the new handle. When you pull the door handle, the latch should release the screwdriver.

Insert your key and test the lock to make sure it is working. Pull the plastic door liner back over the left side of the door. Set the door panel back in place. Turn the key in the ignition and test your window. sliding door lock philippinesIf you hear scratching or scraping noises, put the window back up. fire exit door textureLook for any obstructions keeping the window from moving smoothly up and down.garage door store everett Replace the door panel screws, pins and clips. garage door opener wayne njMake sure the wires for the light are sticking through the door. upvc doors diy installation

Plug the light back in when you reinsert it. Make sure the clips that attach the door panel to the bottom of the door are properly aligned. Push on them to engage them. Pull the inside door handle and slide the trim back over it. jeep wrangler 4 door for sale in new yorkPush on the end without the clasp first, then the end with the clasp. 1996 chevrolet tahoe 2 door for saleTo engage the clasp, push down on it with your screwdriver. If the plastic liner inside your Camry's door tears in the process of replacing the handle, you can cut a piece of plastic garbage bag to fit in its place. Do not put the door panel back on without a liner. Chilton's Toyota Camry 1997-2001 Repair Manual; You May Also Like The Toyota Camry was chosen as the ninth best affordable midsize car by U.S. News and World Report, and has been the...

Exterior door handles on a Toyota Tercel have threaded shafts that extend through the door and have retaining nuts on the inside... There can be a few reasons to change the door handles on a Toyota Camry, like one of the handles getting broken,... Toyota had the do-it-yourself repair person in mind when they designed the 2002 Toyota Camry. They made it easy to replace small... How To Travel For Free With Reward Points How to Install a Driver-side Door Latch on a Toyota Camry Replacement Instructions for a Toyota Outside Door Handle How to Take the Door Panel Off a Toyota Camry How to Repair a Toyota Sienna's Driver Side Handle How to Remove the Rear Wheel Bearing on a 1999 Camry How to Order a Tiburon Door HandleToyota Camry For Sale Find Toyota Camry for sale By Year View All Years of Toyota Camry For Sale 2014 Toyota Camry Review 25 city / 35 hwy 21 city / 30 hwy 22 city / 32 hwy 19 city / 28 hwy 3.0L V6 Natural Aspiration