Garage Door Work Gear Kit Select a Home Store to see Local Pricing Not all items shown are stocked in store but can be special ordered. Please contact your local Home Store for more information. Sign Up & Save Sign up for Home Hardware emails and get exclusive online savings, sneak peeks at money-saving flyers, email-only promotions and much more. For use with all AC powered garage door openers built since 1984 Will not work on battery backup units as they are powered by a DC motor Includes step-by-step replacement instructions along with hardware Works with model #'s 5200HBC (HH #2610-384), 4200C, HB250, 8200C, 550HBC, 5100HBC Sign up for our eFlyerLearn about great deals at your Home Store first!eGift Cards Instant Gift GivingAeroplan Earn Miles HereThe Official Vehicleof Home Hardware © 2017 Home Hardware Stores Limited. All Rights Reserved.Privacy Policy | Terms & Conditions | Return PolicyProudly Canadian Owned and Operated

How to Maintain Your Automatic Garage-Door Opener Your automatic garage-door opener requires periodic maintenance to ensure safe and efficient operation. In fact, because a garage door is often the heaviest and largest single piece of moving equipment around a home, frequent testing and maintenance are especially important. Lubrication requirements and adjustment details are typically found in the owner’s manual. If you don’t have an owner’s manual, you can usually order a replacement copy by contacting an installing dealer or the manufacturer. Some manufacturers even make owner’s manuals available online. All you need is the brand and model number. An inspection of the garage-door springs, cables, rollers, and other door hardware is a great place to begin. Look for signs of wear and for frayed or broken parts. A handy do-it-yourselfer can perform most minor repairs, such as roller replacement, but a qualified garage-door service technician should handle the more complicated tasks.

The springs and related hardware are under high tension and can cause severe injury if handled improperly. Rollers, springs, hinges, and tracks require periodic lubrication. Use spray silicone, lightweight household oil, or white lithium grease according to the instructions in your owner’s manual. Periodically test the balance of the door. Start with the door closed. Disconnect the automatic opener release mechanism so that the door can be operated by hand. The door should lift smoothly and with little resistance. It should stay open around 3 to 4 feet above the floor. If it doesn’t, it’s out of balance and should be adjusted by a professional. Monthly inspection and testing of the automatic opener can prevent serious injuries and property damage. Careless operation and allowing children to play with or use garage-door opener controls are dangerous situations. A few simple precautions can protect your family and friends from potential harm. Never stand or walk under a moving door.

Don’t let children play “beat the door.” Keep transmitters and remote controls out of the reach of children and teach them that they aren’t toys. The push-button wall control should be out of the reach of children (at least 5 feet from the floor) and away from all moving parts. The button should always be mounted where you can clearly see the door. Test the force setting of the opener by holding up the bottom of the door as it closes. If the door doesn’t reverse readily, the force is excessive and needs adjusting. where to buy garage doors saskatoonThe owner’s manual will explain how to adjust the force sensitivity.prices liftmaster garage door opener To avoid entrapment, perform the 1-inch reversing test after any repairs or adjustments are made to the garage door or opener. roll up doors stockton ca

Simply place a 2-x-4 flat on the floor in the door’s path before activating the door. If the door fails to stop immediately and reverse when it strikes the wood, disconnect the opener and use the door manually until the system can be repaired. Here are some of the most common garage door opener problems and their solutions: If the opener raises but won’t close the door, the safety beam sensor may be faulty, misaligned, or unplugged. An opener that operates by remote control but not by the wall switch is a sign of a short in the wiring or a loose connection at the switch.garage door repair concord ca A remote control that doesn’t work may be something as simple as a weak or dead batteries, an antenna wire on the opener that isn’t properly exposed, or a dead transmitter. If the opener is operating but the door doesn’t open, the problem may be due to a worn gear or chain-drive sprocket, a broken chain, or the door disengaging from the operator.

A faulty transmitter, a short in the wall switch, a faulty circuit board, or a stray signal (which is very rare) can cause an opener to operate by itself. If the remote control only operates the door when it’s located 25 feet or less from the opener, the battery in the remote is weak or the signal is poor. A door that reverses while closing or that doesn’t completely open or close is usually obstructed or binding. This condition can also be caused when the open limit or sensitivity is set wrong. A straining opener usually occurs when safety reversing is activated or the close limit is set improperly. Most Common Garage Door Repair CostsWhy doesn't Angie's List rate attorneys?Landscaping: What do your neighbors do that drives you crazy?How much does it cost to be a member here?How much does it typically cost to paint a 2100 square foot house on the exterior? That's very difficult to answer without seeing the house. As one poster said, the prep is the most important part.

On newer homes that don't have a lot of peeling paint, the prep can be very minimal even as low as a couple or a few hundred dollars for the prep labor. On a 100 year old home with 12 coats of peeling paint on it, then the prep costs can be very high and can easily exceed 50% of the job's labor cost.A 2100 sq ft two story home could easily cost $1000 just for the labor to prep for the paint job. That number could climb too. Throw in lots of caullking  or window glazing, and you could be talking a couple or a few hundred dollars more for labor. Painting that home with one coat of paint and a different color on the trim could run roughly $1000 or more just for labor. Add a second coat  and that could cost close to another $1000 for labor. For paint, you may need 20 gallons of paint. You can pay from $30-$70 for a gallon of good quality exterior paint. The manufacturer of the paint should be specified in any painting contract. Otherwise, the contractor could bid at a Sherwin-Williams $60 per gallon paint and then paint the house with $35 Valspar and pocket the difference.