To utilise the space normally taken up by a hinged door we offer cavity door units allowing the door to slide into a pocket in the wall. (Download PDF for price excluding GST)How to install a cavity door We take you through the steps to install a cavity door unit. Phillips Head Screw Driver Ear, Eye & Dust Protection Timber Pelmet cover trims Closing Jamb (VIC, SA, TAS, WA only) 2. Measure your opening Measure your stud opening (insert image #1) allow 5mm minimum in both height and width. This will allow for the unit to be packed square during installation. Use these measurements to purchase your new Hume cavity. Height = Door Height + 70mm (QLD, VIC, SA, TAS, WA) Height = Door Height + 80mm (NSW, ACT) Width = 2 x Door Width + 10mm – Flush Pull (Door protrudes 50mm) Width = 2 x Door Width + 60mm – Flush Jamb (Door is flush with split jamb) 3. Remove transport plates Remove both transport plates from the top of the cavity.

Fit and screw steel head/track to the top of the cavity unit. 4. Fit closing jamb to head/track Fit closing jamb to head/track. (Not supplied QLD, NSW, WA, ACT) 5. Place cavity unit in opening Stand assembled cavity unit into your opening, ensure unit is level, pack behind then fix through back post of the cavity unit into the house frame. garage door repair sunrise flMake sure the split jambs are in line with the house frame and fix the unit to the floor. pocket door frame johnson hardware(pack under cavity for additional clearance under the door - only if required)upvc door lock barrel removal 6. Fix head track to framecar glass repair arlington va

Ensure split jambs and head/track are plumb and level, then fix the head to the house frame. 7. Make sure closing jamb is plumb Plumb closing jamb, pack and fix through to the house frame. 8. Cavity fittings pack includes 2 x 4 Wheel Roller Assembliesbifold shower door chrome L/H & R/H Door Guidesbi folding doors upvc vs aluminium 2 x Quick Release Base Platesfront door canopy south wales Rubber Bumper Stopper (QLD only) 9. Fit 4 wheel roller cariages into head track Place both 4 wheel roller carriages into the track and ensure they both operate well. Check that the door is straight and free of any imperfections. Seal your door top & bottom with two coats of undercoat and 2 coats of paint.

Refer to manufacturer's warranty. 11. Attach the base plates Attach the base plates on the top edge of the door, 80mm from each end. Ensure the nylon lock tabs are both on the same side of the door. 12. Fit clad to opening Clad your opening (Not included) - Important - At this stage make sure the temporary spacer block and plate (located in between the split jambs, approximately half way up from the bottom) remain in place during cladding and tiling to prevent distortion of the cavity pocket. Remove after cladding and prior to the door installation. 13. Fit the architraves. 14. Slide the carriage pin into the base plate Check the opening is free from obstructions, slide the door into the cavity, lift door and slide the carriage pin into the base plate. Then lock with the tab and repeat this process for the second wheel carriage. 15. Fit the cavity door guides Fasten the door guides at the bottom of the split jamb. Ensure the slide adjustment part of the guide is on the outside of the opening.

Check the door slides evenly and smoothly. 16. Adjust the height of the wheel carriage Using the adjusting spanner, adjust the height of the wheel carriage and plumb against closing jamb. 17. Cut timber cover trims Cut the timber cover trims to the desired length, fix with screws provided. 18. Fit screw covers Fit all the screw covers to the timber pelmet cover trims. Check your door operates correctly and revisit any of the steps if required.Cowdroy Products Ltd is the manufactuer of Cavity Door Pockets. We do a full range of standard pockets as well as custom made specials, anything from a 70mm stud right up to a 190mm stud. Our pockets come to you fully assembled to save time and make installation effortless. We can also supply and fit standard and special doors, you can even drop your own door off to us to be fitted into a cavity. Cavity Pockets are a great way to save space in a house and also eliminate any slamming doors when a breeze blows through.

All our cavities come with removable head jambs for ease of access to the top of the door for adjustments. Below is a list of the most common available options. If what you are after is not listed, please make an enquiry below. Where there is a need for a cavity slider to be fitted into a 3 inch wall, the Cowdroy Products Ltd 70mm Optimiser™ cavity unit is the perfect choice. With all the functionality of a standard 90mm cavity slider, you will be able to retain the existing wall thickness in keeping with the design of your home.These units are supplied with pine flat or grooved jambs to suit 10 or 13mm linings, and are made to suit door sizes 1980 high and 610 to 910 wide. Our Standard Optimiser Cavity Sliders can be assembled in either 90mm Stud or 94mm Stud. Our stock standard sizes range to suit door sizes 1980h and 610-910 wide. They can be made with Flat pine or Grooved Pine Jambs to suit 10mm or 13mm Gib Linings. We can custom make Cavities to suit the customers requirements.