To find a locksmith near to you specialising in repairing door & window locks Please enter your postcode or location in the search box below. There are number of reasons why a UPVC Door or Window lock will need repairing if it is broken or damaged, you will either be able to fix the problem or you might need a lock replacement.  Our advice is to contact your nearest local locksmith who will be able to advise you on the best solution. USE THE SEARCH BOX ABOVE or Click here to Find your Local Locksmith UPVC door and window locks are commonly found on your common domestic homes front & back doors, and also can be found on french and patio doors.  A MLA approved locksmith will deal with the below problems on a daily basis and will be able to help you: This problem is usually indicative of one of two things usually but can be a combination of both, the two main mechanical parts to a upvc/composite door are the euro profile cylinder lock and the multi point locking mechanism.

If the key does not go into the lock cylinder (sometimes called euro lock) all the way in, or the key will go in and not turn usually this is a euro cylinder failure. So this part needs to be replaced once the door has been opened. Common reasons this happens are usually because the euro lock worn, a cheap lock has been fitted, the key has been left on the inside and lock operated from other side and the lock is now out of sync, or general wear and tear. If the key goes into the euro lock and turns anti clockwise (unlock) one complete turn and the door won’t open this is usually a sign that the multi point lock has failed or a security bolt or hook has jammed. Common reasons this usually happens are: door and frame not fitting correctly or are out of alignment and the handles have been forced up to lock and the delicate mechanism has broken, general wear and tear, or possibly that the door is slammed constantly. Find a Local Locksmith now to help repair the lock

This is commonly caused by either the strike receiver for latch part of lock not being adjusted correctly or having worked loose and now not being set correctly, or the door trim rubber has moved and is not sitting properly on door stopping the door from shutting correctly. Upvc door/window lock is very notchy when lifting the upvc door or window handle is usually due to a worn or faulty locking mechanism. When a key goes into euro profile cylinder but you have to jiggle or pull key up or down is usually a sign of badly cut keys or a faulty or worn euro cylinder lock.upvc door panel manufacturers uk One of the multi point hooks or bolts won’t retract in or out properly when the window handle or upvc door handle is operated is usually a sign of a broken mechanism or locking security device.wooden garage doors worcestershire

The reason a key is usually needed to change a euro profile cylinder lock is the cam on the lock (the part that locks the handle which in turn operates the upvc mechanism when the key is turned) needs to be in line with the euro lock body to remove from the door. If you have no keys and the euro cylinder retaining screw is removed in the usual way the euro lock will NOT slide out as the cam is in the wrong position stopping the euro lock from being removed.impact resistant sliding glass doors cost MLA approved locksmiths will be able to attend site and change the euro lock even if no key is available by using an array of specialist tools and knowledge to align the cam in the correct position to remove the euro profile cylinder lock without damaging the door.fire exit door checklist

Locksmiths can repair or replace many different types of upvc locking mechanisms usually on site. Upvc locking mechanisms have evolved over time with the security levels offered originating with the latch and roller style mechanism’s and now usually latch, deadbolt and hook variants on offer from most high security upvc/composite door sets. MLA locksmiths can also usually upgrade any out of date upvc multi point locking mechanisms for the higher security, hook and bolt style higher security locking units. frameless shower door ratingsHelping also usually as well with high security door furniture (e.g. security handles and the latest offerings of euro profile locking technology with anti snap, bump, pick, drill locks available today.auto glass repair providence Popular makes of multipoint lock consist of ERA, GU, YALE, FULLEX, CEGO, MACO, MILA, AVOCET, WINKHAUS, LOCKMASTER, FUHR to name a few.upvc door handles no lock

Common types of security on upvc/composite locking units consist of: 1. Window or door strikes are not in the correct position to allow the mechanism to reach the fully locked correct position or handle to reach maximum lift position to allow the key to turn on upvc/composite doors. 2. Hinges may require adjusting to allow correct fitting of door and frame or window and frame. 3. Rubber surrounding window or door not sitting correctly. 4. Mechanical failure of part either locking mechanism in window or door, euro cylinder or hardware problem with broken or worn lock furniture usually (locking window handle or upvc door handles) Should you have any of the above problems, need your upvc door or window locks replacing or repairing then contact a MLA approved locksmith who will be able to provide expert advice. Click here to Find your Local LocksmithEdit ArticleHow to Fix a Sticky Lock Two Methods:Spraying the Lock with WD-40Lubricating the Lock Using Powdered GraphiteCommunity Q&A

After enough use, you might find that your door lock has begun to “stick,” making it difficult to put in, turn or pull out your key. This occurs when dust, dirt, grime and other buildup accumulates on the internal mechanisms that control the movement of the lock. Sticky locks can be extremely frustrating, and it’s likely the last thing you want to deal with when you’re coming home at the end of a long day. Luckily, it only takes one or two inexpensive products and a couple of minutes to get your lock moving smoothly again. Buy a can of WD-40. Run down to your local hardware store and purchase a can of WD-40. WD-40 is a common household lubricating oil that can be used on everything from bicycle chains to door hinges. If your lock isn’t in real bad shape, a little squirt of WD-40 will probably be all you need. WD-40 is generally a great product to have on hand whenever there’s a need for an all-purpose lubricant. Avoid using any lubricants that aren’t appropriate for home improvement use, such as cooking, botanical or sewing machine oil.

Most oils will just attract dust that then forms new layers on the locking mechanism, making the problem worse. Attach the applicator straw to the nozzle of the can. Hook up the red applicator straw that comes included with the can of WD-40. These straws are thin and flexible and fit right over the opening of the nozzle where the oil comes out. The addition of a straw will allow you to penetrate deep into the inner workings of the lock, lubricating it more effectively. Some newer containers of WD-40 feature permanently-attached straws. Keep an eye out for these, as they’re just what you need. A straw will also keep the spray of the lubricant confined inside the lock where you want it, rather than all over your front door. Insert the straw into the opening of the lock. Spray the WD-40 into the lock. Press down on the button on the rear of the WD-40 canister to begin releasing the lubricant into the lock. Don’t be afraid to use a liberal amount of oil—a sticky lock needs the attention.

Hold down the spray button until the WD-40 begins to overflow from the lock opening. Wearing gloves while handling lubricants can help prevent a slippery mess.Let the WD-40 sit for a few minutes. This will give it a chance to start breaking down the dust and dirt accumulated inside the lock that’s impairing its movement. Once it’s had some time to set up, slide your key in and out of the lock a few times and observe how smoothly it moves. If it doesn’t meet resistance, your work is done. If the lock still sticks a bit, you may need to try a more heavy-duty lubricant such as powdered graphite. Make sure you’ve properly coated each part of the locking mechanism by running through the locking and unlocking action a few times. After you've applied WD-40 to the lock, the interior pins should disengage with no resistance and the cylinder should easily rotate when you turn your key. Lubricate the locks around your home with WD-40 regularly to keep them maintained. Get a tube of powdered graphite.

Powdered graphite is a special dry lubricant that can be found in most hardware or department stores. It is designed to encourage smooth movement between two surfaces without attracting grime, which means it won’t gum up like oil-based lubricants. If your lock is so sticky that you can barely get your key in and out, you may need something as tough as powdered graphite. Once applied, the graphite particles form a fine layer on the surface of the metal, lubricating and “brushing” away dust and dirt. A small container of powdered graphite can be purchased in most places for as little as $2. Cut the plastic tip off the end of the bottle. Most containers of powdered graphite have a solid plastic film covering the tip that will need to be removed prior to use. Take a utility knife or sharp pair of scissors and snip the plastic off the end of the nozzle. Be sure to make a large enough opening that the graphite can flow freely. Hold the tip of the bottle up to the lock. Place the end of the nozzle up to the opening of the lock.

Depending on the size of the bottle, you may be able to actually fit the nozzle part of the way inside the opening. If not, just hold it flush to the lock. It should still be able to penetrate deep enough to lubricate the locking mechanism. Make sure you’re holding the bottle level so that graphite doesn’t escape around the opening. Consider covering the area of your door around the lock to guard it from stray graphite particles Inject some powdered graphite into the lock. Squeeze the bottle gently to release a few puffs of powdered graphite into the lock. Try not to use an excessive amount—graphite is a potent substance, so a little bit will go a long way. Allow the graphite to start working on the lock for a minute or two. Start by using a little bit of lubricant and apply more if the lock still sticks. Handle powdered graphite carefully. Otherwise, the fine black dust can get everywhere, staining surfaces and creating a big mess. Try your key in the lock.

Test the lock by inserting and removing your key once or twice. You shouldn’t have any trouble getting it in and out of the lock now. Turn the key in both directions to see how fluidly it moves. Sliding your key in and out of the lock will help spread the graphite around inside to the place where it most needs to be.If the lock still feels a little sticky, hit it again with a few more blasts of powdered graphite. Test the lock after each application. Once the graphite has distributed through the lock, it will begin to clear away the gunk that’s been hindering the lock’s movement, leaving you with a fully functioning, hassle-free door. For especially stubborn locks, try squeezing a little graphite onto the door’s latch as well. This is the part of the locking mechanism that moves in and out of the door frame when you turn the knob. Lubricating the latch can help ease the keying action. If you still don’t have any luck after trying powdered graphite, call a professional locksmith to come out and take a look at your locks.

Always wash your hands if your exposed skin comes into contact with WD-40 or powdered graphite. Keep WD-40 and powdered graphite stored somewhere accessible in your home so that you'll have them on hand when your locks start acting up. Aim to lubricate your door locks once a year or so to keep them functioning the way they should, even if they haven't yet gotten sticky. The problem may not always be with the lock. Inspect your keys for signs of damage and overuse. Have new ones cut if they're considerably worn down. Dull key teeth can have difficulty displacing the pins inside a lock. If you're still having trouble with your lock after treating it with powdered graphite, it probably needs to be disassembled and cleaned manually, or replaced altogether. Use powdered graphite sparingly. Graphite tends to be overused, and will eventually start to cake onto a lock, making it harder to operate. Be careful not to inhale graphite particles. This could lead to illness or infection.